Custom Alumina and Zirconia Ceramic Components

Custom alumina and zirconia ceramic components specified by drawing, including blocks, plates, tubes, rods, rings, sleeves and pins. Define the material grade, finished dimensions, tolerances and quantity for your industrial component enquiry.

SKU: 685989200212 Category:
somdn_product_page

Description

Custom alumina and zirconia ceramic components

IKSONIC custom ceramic components cover alumina and zirconia parts specified by a drawing or a clearly defined dimension schedule. The range includes blocks, plates, tubes, rods, rings, sleeves and pins for industrial component enquiries. A straightforward ring and a stepped, drilled or grooved part require different details, so the enquiry should identify the complete finished geometry rather than only the general shape.

Use this listing for a custom component requirement, including insulating-part enquiries where the required electrical properties are defined separately. The material family, finished dimensions, critical interfaces and quantity form the basis of the specification. The photographs illustrate different component forms; they do not define a standard-size set, an included assortment or a particular material grade for every pictured piece.

Product specification overview

Item Specification
Product type Custom industrial ceramic components
Material families Alumina and zirconia; specify the required grade for the individual part
Component forms Blocks, plates, tubes, rods, rings, sleeves and pins
Size selection Dimensions and units defined by the drawing or agreed dimension schedule
Geometric details Identify required bores, steps, grooves, holes, slots and edge features on the part drawing
Dimensional tolerances Specify critical tolerances and a general tolerance requirement separately
Surface requirements Identify functional surfaces and state the required finish or inspection criteria
Quantity State the number of pieces required for each drawing or part number

Define the geometry that matters to the assembly

Begin with the outer envelope, then describe the features that locate, support or connect the component. Keep overall dimensions separate from local feature dimensions. Where a part has several steps or repeated holes, use reference faces and clear feature locations so the intended geometry is unambiguous.

  • Blocks and plates: give length, width and thickness, then locate holes, slots, recesses and edge details. Mark the faces that contact or locate another component and identify any required flatness or parallelism.
  • Tubes, rings and sleeves: specify outside diameter, inside diameter and overall length or thickness. Show shoulders, grooves and changes in bore diameter separately. Identify which surfaces control the fit.
  • Rods and pins: give the diameter and overall length, with separate dimensions for stepped sections, end forms, cross-holes or locating features. State any required straightness or relationship between diameters.
  • Mixed-feature parts: include the relationship between holes, slots, faces and axes. A photograph can help explain the shape, but a dimensioned drawing provides the information needed to define the finished part.

Specify material and service requirements together

Choose the material family together with the requirements of the component and its assembly. If a design already calls for a particular alumina or zirconia grade, include that designation in the enquiry. If grade selection is still open, describe the intended function and the conditions the part will encounter so the requirement can be reviewed without treating all ceramic grades as interchangeable.

For an insulating component, state the required electrical properties and how they will be assessed. For a part exposed to heat, contact loading, wear or chemicals, identify the actual exposure conditions and any acceptance criteria. Required performance should be tied to the selected material grade and finished part; no universal hardness, strength, electrical rating or operating-temperature limit is assigned to this custom range.

Information to include with an enquiry

Requirement Details to provide
Part identification Part number, drawing number and revision; identify each different component separately
Dimensions Dimensioned drawing or complete dimension schedule, with units and reference faces or axes
Material Alumina or zirconia, specified grade if known, and any mandatory material requirements
Fit and geometry Mating-part dimensions, critical clearances, tolerances and feature relationships
Surface and edges Functional surfaces, finish requirements, chamfers, radii and any defined edge acceptance criteria
Operating conditions Intended function, relevant temperature exposure, electrical requirements, loading or contacting media
Inspection and documents Required measurements, acceptance criteria and any requested material or inspection documentation for review
Quantity Required piece count for each part and any separate prototype or repeat-order requirement

Replacement parts and drawing revisions

For a replacement component, distinguish the intended finished dimensions from measurements taken on a worn or damaged example. Record the mating features and the space available in the assembly as well as the component itself. If a sample or photograph accompanies the enquiry, identify any features that are damaged, missing or intentionally changing.

Keep the drawing revision consistent across dimensions, material requirements and quantity lists. Mark changes to bores, shoulders, grooves or contact faces clearly rather than relying on a similar-looking photograph. Send the complete specification to IKSONIC for a custom ceramic component enquiry; the final configuration and order details are agreed for the individual requirement.

If you have any questions or products request, please leave message or call us.

Email: [email protected]
WhatsApp/Mobile/WeChat: +86-13370616532  , +86-15315489052
WeChat: taishanfu
Skype ID: wingxsonic
Scan the QR code above, add me on WeChat iksonic.com rubber plastic steel factory

Scan the QR code above, add me on WeChat.

Add us on WhatsApp

Add me on WhatsApp Contact by Scanning QR.

    Questions ?

    If you need any products, please let us know. We will answer you within 1 hour to 12 hours.

    Your Name (required)

    Your Email (required)

    Your Phone (required)

    Your Country

    Your Message

    Additional information

    Material family

    Alumina, Zirconia

    Component forms

    Blocks, Plates, Tubes, Rods, Rings, Sleeves, Pins

    Specification basis

    Custom drawing or dimension schedule